1PCS 1MHz-1.1GHz 1Hz-50MHz Crystal Oscillator Tester Frequency Counter Meter

Description

Features:
Yellow
- This document describes the construction of small frequency counter with a cheap PIC microcontroller and a few seven-segment LED digits.
- Frequency range 1 Hz ... 50 MHz
- Five digits resolution (display for example x.xxxx kHz, x.xxxx MHz,
or xx.xxx MHz)
- Measuring signal amplitude can be up to 30 v
- 4-40 m passive crystals can measure
- Automatic range switching with different gate times
- Optional addition or subtraction of a frequency offset (programmable)
- Very low component count: a PIC 16F628, 5 7-segment LED displays, a 20MHz crystal and a few resistors
- Optional (configurable) power-saving mode which automatically turns
- The display off if the frequency didn't change significantly within 15seconds
- USB 5V or DC5-12V power supply can be used
Package included:
1x DIY Kits
(DIY kits, not assembled
)
1x USB cable
Red
Color: Red
SIze: 8 x 5.4cm
Suitable For:
Crystal measure (4M, 16M crystal)
Crystal measure (20M, 11.0592M crystal)
Features
This is a PIC microcontroller-based frequency meter, subtraction frequency is set with
crystal measurement functions and programmable, five digital display, easy and intuitive,
all using in-line components, the circuit is simple and easy to make
1. measurable frequency range of 1 Hz -50 MHz (1Hz-50MHz);
2. The most commonly used measure of the oscillation frequency of the crystal;
3. Five-digit precision resolution (eg 0.0050 kHz, 4.5765 MHz, 11.059 MHz);
4. Automatic range conversion, without human handover;
5. Programmable subtraction frequency setting, such as a transceiver for measuring equipment;
6. selectable power saving mode within 15 seconds if there is no significant change in the frequency automatically turn off the display;
7. You can use a common USB 5V interface, power supply, can also use an external DC power supply or 9V battery.
8. A small number of elements, all in-line components, installation is simple.
Instruction manual
1. All line elements, PCB printing press to the correct welding,
2. After welding is completed with a standard source input signal,
3. Adjust the yellow adjustable capacitor so that the display is equal to the value of the signal frequency
Packing Included
：
1 x 1Hz-50MHz frequency meter
(DIY kits, not assembled,No Case)
Frequency Counter
Use 8 bit Microchip PIC16F648A,up to 1.1GHz
Gate time
0.64 seconds
Test sensitivity
1 MHz ~ 10 MHz: superior 60mVpp
10 MHz ~ 60 MHz: superior 60mVpp
60 MHz ~ 1.1 GHz: not tested
3) . Frequency reference
5032 package 13.000 MHz Warming voltage controlled crystal oscillator ( VC - TCXO) , frequency stability is ± 2.5 ppm
IF settings
The minimum frequency is adjustable in steps of 100 Hz, frequency range 0 ~ 999.9999 MHz, can be set to plus or minus IF mode
working voltage
DC input: DC 9V ~ 12V
working current
The backlight is enabled: ≤ 55 mA backlight disabling: ≤ 55 mA
Display
maximum of 8 digit display
physical dimensions
Length * width * height: 58mm × 32mm × 27mm
Board interface
RF INPUT ( measuring signal input ): XH2.54-2P side outlet port
ICSP INPUT (MCU programming interface ): XH2.54-6P pins
POWER INPUT ( Power Interface ): XH2.54-2P side outlet port
Package included:
1 x Frequency Counter Tester Measurement For Ham Radio
Contact us
Return Policy
Feedback
Contact us
For anything problem about product, price, shipping or order status, pleasecontact us via eBay message.Just contact us using the "Ask the seller a question" link on eBay.
We expect positive feedback and 5 scores DSR  from you.
Return Policy
We believe our items are so outstanding. We are convinced you will be happy with your Purchase.
If you do not satisfy with our items. Please simply return to us within 30 Days in original condition. Just pay for the returned postage. Then we can issue full refund to you after the returned item arrived at our warehouse.
Please include your eBay ID and item number with any email requests.
Feedback
* When you satisfied with our product and services please leave us positive feedback.
* If you have got the package, please confirm "Delivery on time" For us.
* If a problem occurs, contact us immediately with any email request.
* Just contact us using the " Ask the seller a question" link on eBay.
Your Satisfaction is our Priority. Our goal is to make all our customers as happy as possible while shopping with us.
On Dec-22-18 at 06:54:03 PST, seller added the following information: